|  | =pod | 
|  |  | 
|  | =head1 NAME | 
|  |  | 
|  | SSL_set_shutdown, SSL_get_shutdown - manipulate shutdown state of an SSL connection | 
|  |  | 
|  | =head1 SYNOPSIS | 
|  |  | 
|  | #include <openssl/ssl.h> | 
|  |  | 
|  | void SSL_set_shutdown(SSL *ssl, int mode); | 
|  |  | 
|  | int SSL_get_shutdown(const SSL *ssl); | 
|  |  | 
|  | =head1 DESCRIPTION | 
|  |  | 
|  | SSL_set_shutdown() sets the shutdown state of B<ssl> to B<mode>. | 
|  |  | 
|  | SSL_get_shutdown() returns the shutdown mode of B<ssl>. | 
|  |  | 
|  | =head1 NOTES | 
|  |  | 
|  | The shutdown state of an ssl connection is a bitmask of: | 
|  |  | 
|  | =over 4 | 
|  |  | 
|  | =item Z<>0 | 
|  |  | 
|  | No shutdown setting, yet. | 
|  |  | 
|  | =item SSL_SENT_SHUTDOWN | 
|  |  | 
|  | A "close notify" shutdown alert was sent to the peer, the connection is being | 
|  | considered closed and the session is closed and correct. | 
|  |  | 
|  | =item SSL_RECEIVED_SHUTDOWN | 
|  |  | 
|  | A shutdown alert was received form the peer, either a normal "close notify" | 
|  | or a fatal error. | 
|  |  | 
|  | =back | 
|  |  | 
|  | SSL_SENT_SHUTDOWN and SSL_RECEIVED_SHUTDOWN can be set at the same time. | 
|  |  | 
|  | The shutdown state of the connection is used to determine the state of | 
|  | the ssl session. If the session is still open, when | 
|  | L<SSL_clear(3)> or L<SSL_free(3)> is called, | 
|  | it is considered bad and removed according to RFC2246. | 
|  | The actual condition for a correctly closed session is SSL_SENT_SHUTDOWN | 
|  | (according to the TLS RFC, it is acceptable to only send the "close notify" | 
|  | alert but to not wait for the peer's answer, when the underlying connection | 
|  | is closed). | 
|  | SSL_set_shutdown() can be used to set this state without sending a | 
|  | close alert to the peer (see L<SSL_shutdown(3)>). | 
|  |  | 
|  | If a "close notify" was received, SSL_RECEIVED_SHUTDOWN will be set, | 
|  | for setting SSL_SENT_SHUTDOWN the application must however still call | 
|  | L<SSL_shutdown(3)> or SSL_set_shutdown() itself. | 
|  |  | 
|  | =head1 RETURN VALUES | 
|  |  | 
|  | SSL_set_shutdown() does not return diagnostic information. | 
|  |  | 
|  | SSL_get_shutdown() returns the current setting. | 
|  |  | 
|  | =head1 SEE ALSO | 
|  |  | 
|  | L<ssl(3)>, L<SSL_shutdown(3)>, | 
|  | L<SSL_CTX_set_quiet_shutdown(3)>, | 
|  | L<SSL_clear(3)>, L<SSL_free(3)> | 
|  |  | 
|  | =head1 COPYRIGHT | 
|  |  | 
|  | Copyright 2001-2016 The OpenSSL Project Authors. All Rights Reserved. | 
|  |  | 
|  | Licensed under the OpenSSL license (the "License").  You may not use | 
|  | this file except in compliance with the License.  You can obtain a copy | 
|  | in the file LICENSE in the source distribution or at | 
|  | L<https://www.openssl.org/source/license.html>. | 
|  |  | 
|  | =cut |